Skip to content

Air and Heat Guide

  • Cooling
    • Air Conditioning
    • Heat Pumps
  • Heating
    • Furnaces & Heating
    • Heat Pumps
    • Thermostats
  • Error Codes
  • Air Quality
  • Costs
  • Maintenance

Thermostat Clicking but Nothing Happens? What It Means and 7 Fixes

November 12, 2026 by Dave Harlan
Finger pressing the up button on a white digital wall thermostat showing 72 degrees

A thermostat click means it is sending the signal, so the problem is usually the equipment: a compressor delay, no power at the furnace, a tripped float switch or a loose wire.

Categories Thermostats

Furnace Blower Won’t Turn Off? 7 Causes and Fixes

November 12, 2026 by Dave Harlan
Person shining a flashlight on the blower fan wheel inside an open gas furnace in a basement

If the furnace blower runs nonstop, check the thermostat fan setting first. Then overheating, a stuck fan relay, a wiring short or a fan limit switch set to manual. How to find which one.

Categories Furnaces & Heating

Heat Pump Short Cycling in Winter: Causes and Fixes

November 9, 2026 by Dave Harlan
Outdoor heat pump unit on a frosty winter morning with steam rising from it

A heat pump that turns on and off every few minutes in winter is short cycling. How to tell it from normal defrost, the common causes from thermostat to refrigerant, and what you can check yourself.

Categories Heat Pumps

Ecobee Not Heating? 7 Fixes, Including “Calibrating”

November 9, 2026 by Dave Harlan
Square smart thermostat showing 62 degrees and Heat On while a person in a sweater warms their hands in a cold living room

If your ecobee is not heating, check for Calibrating, the mode and setpoint, power and the C wire, wiring, and the equipment settings in the ecobee. When it says it is heating but the house stays cold, the problem is usually the furnace or heat pump.

Categories Thermostats

Furnace Inducer Motor Problems: Signs, Codes and Repair Cost

November 5, 2026 by Dave Harlan
Inducer fan motor with grey PVC exhaust pipe at the top of an open gas furnace

A failing inducer motor stops a gas furnace from lighting at all. The signs, how to tell it from a pressure switch or venting problem, error codes by brand and what repair costs.

Categories Furnaces & Heating

Nest Thermostat Using Aux Heat Too Much? Heat Pump Balance Explained

November 5, 2026 by Dave Harlan
Round smart thermostat showing 68 degrees with AUX heat on, snowy backyard through the window

If your Nest keeps showing AUX and your bills are climbing, Heat Pump Balance is the setting to change. What Max Comfort, Balanced and Max Savings do, how to change them and other reasons aux heat runs too much.

Categories Thermostats

Furnace High Limit Switch Tripping: Why It Happens and How to Fix It

November 12, 2026November 2, 2026 by Dave Harlan
Gloved hand pointing at a safety switch inside an open gas furnace with blue burner flames behind it

A tripping high limit switch shuts off the burners while the blower keeps running, so you get cold air. It is almost always an airflow problem. Causes, error codes and fixes.

Categories Furnaces & Heating

Furnace Pressure Switch Problems: Causes, Error Codes and Fixes

November 5, 2026November 2, 2026 by Dave Harlan
Furnace pressure switch with a clear rubber hose connected to the inducer motor housing inside a gas furnace

Inducer runs but the furnace never lights? The pressure switch is usually telling you the vent, drain or hose is blocked. Error codes by brand, causes and what you can safely check.

Categories Furnaces & Heating

Thermostat Says Heat On but No Heat? 9 Checks to Find the Cause

November 12, 2026October 29, 2026 by Dave Harlan
Hand checking a floor heating vent for warm air in a cold room with a thermostat on the wall and frost on the window

If the thermostat says it is heating but the house stays cold, the signal is not reaching the furnace, the furnace will not light, or the heat is not reaching you. Nine checks in order.

Categories Thermostats

Honeywell Thermostat “Recovery”: What It Means and How to Turn It Off

October 29, 2026 by Dave Harlan
Digital wall thermostat showing Recovery above a room temperature of 64 degrees with a flame icon

“Recovery” on a Honeywell thermostat means it started heating or cooling early to reach your next scheduled temperature on time. How it works, when it signals a problem, and how to turn it off.

Categories Thermostats
Older posts
Page1 Page2 … Page7 Next →

Recent Posts

  • Thermostat Clicking but Nothing Happens? What It Means and 7 Fixes
  • Furnace Blower Won’t Turn Off? 7 Causes and Fixes
  • Heat Pump Short Cycling in Winter: Causes and Fixes
  • Ecobee Not Heating? 7 Fixes, Including “Calibrating”
  • Furnace Inducer Motor Problems: Signs, Codes and Repair Cost

Categories

  • Air Conditioning (10)
  • Costs (9)
  • Error Codes (5)
  • Furnaces & Heating (11)
  • Heat Pumps (8)
  • Indoor Air Quality (2)
  • Maintenance (5)
  • Thermostats (16)
  • About
  • Editorial Policy
  • Contact
  • Privacy Policy
  • Affiliate Disclosure
© 2026 Air and Heat Guide • Built with GeneratePress